ALUMINIUM PLAIN & STUCCO SHEET

NAM EXIM can supply high quality plain coil for general engineering and for special applications. Prism can produce plain coils form Hot mill route as well as concast route as well as concast route. The coils are supplied in Mill finish. Stucco Embossed coils can also be supplied.

PACKING

Individual Coils : Strapped With iron hoops, Wrapped With HDPE, Placed on Wooden Box
Wooden Box With edge protector & interleaving with poly film.

CHEMICAL COMPOSITION %
Alloy Si Fe Cu Min Mg Cr Zn Ti Al
1050 0.25 max. 0.40 max. 0.05 max. 0.05 max. 0.05 max. - 0.05 max. 0.03 max. 99.50 min.
1060 0.25 max. 0.35 max. 0.05 max. 0.03 max. 0.03 max. - 0.05 max. 0.03 max. 99.60 min.
1070 0.20 max. 0.25 max. 0.04 max. 0.03 max. 0.03 max. - 0.04 max. 0.03 max. 99.70 min.
1100 0.95 max. 0.95 max. 0.05-0.20 0.05 max. - - 0.10 max. - 99.00 min.
1200 1.00 max. 1.00 max. 0.05 max. 0.05 max. - - 0.10 max. 0.05 max. 99.00 min.
3003 0.6 max. 0.7 max. 0.05-0.20 1.0 – 1.5 - - 0.10 max. - Rem
3005 0.6 max. 0.7 max. 0.30 max. 1.0 – 1.5 0.2 – 0.6 0.10 max. 0.25 max. 0.10 max. Rem
3105 0.6 max. 0.7 max. 0.30 max. 0.30 – 0.8 0.20 – 0.8 0.20 max. 0.40 max. 0.10 max. Rem
5005 0.30 max. 0.7 max. 0.20 max. 0.20 max. 0.50 – 1.1 0.10 max. 0.25 max. - Rem
5052 0.25 max. 0.40 max. 0.10 max. 0.10 max. 2.2 – 2.8 0.15 - 0.35 0.10 max. - Rem
5086 0.40 max. 0.50 max. 0.10 max. 0.2 – 0.7 3.5 – 4.50 0.05 - 0.25 0.25 max. 0.15max. Rem
8011 0.50 – 0.9 0.6 – 1.0 0.10 max. 0.20 max. 0.05 max. 0.05 max. 0.10 max. 0.08max. Rem
                   
ALLUMINIUM SHEET RANGE
Alloy Temper Thickness (mm) Width (mm) Length (mm)
1050 / 1060 / 1070 H1 / H2 / H3 / H4 / O 0.40 – 50 500 - 1500 1000 - 5500
1100 / 1200 / 8011 H1 / H2 / H3 / H4 / O 0.40 – 50 500 - 1500 1000 - 5500
3003 / 3105 / 3005 H1 / H2 / H3 / H4 0.40 – 50 500 - 1500 1000 - 5500
5005 / 5052 / 5086 / 5754 H1 / H2 / H3 / H4 0.40 – 50 500 - 1500 1000 - 5500
         

Note : Aluminum Plain Coils & Stucco Embossed Colis Can be supplied in half of the Thickness Tolerances mentioned in the table against specific requirements. Coils in specification other than those mentioned can also be supplied subject to confirmation.

Note : MOQ conditions shall apply.

Specified Thickness Tolerance (± mm)
Over Thru Upto 1000mm Width Over 1000mm Width
0.40 0.63 0.05 0.08
0.63 0.80 0.06 0.09
0.08 1.00 0.07 0.10
1.00 1.20 0.08 0.11
1.20 1.60 0.08 0.12
1.60 2.00 0.09 0.14
2.00 2.50 0.10 0.16
2.50 3.20 0.12 0.18
3.20 4.00 0.14 0.22
       
COIL I.D (MM) THICKNESS
200 0.18 TO 0.40
300 0.40 TO 0.90
400 / 500 0.90 TO 4.00
 
Width Tolerance
± 2 mm
Coil Density
Max. 3 Kgs / mm width (Hr route) / Max. 5.25 Kgs / mm width (Caster route)