Aluminium plain & Stucco Sheet

NAM EXIM can supply high quality palin sheets for general engineering and for special applications. Prism can offer plain sheets from Hot Mill route as well as concast route. The sheet are supplied in Mill finish. Stucco Embossed Sheets can also be supplied.

PACKING

Individual Coils : Strapped With iron hoops, Wrapped With HDPE, Placed on Wooden Pallet
Wooden Box / Wooden Pallet With edge protector & interleaving with poly film.

Alloy Wirerod

This specification Covers the aluminium alloy rod of about 9.5 mm diameter wihich is used after drawn down in manufacturing conductors type (AAAC) (all aluminium alloy conductors)
The material will be heat treated after the continous casting process and does not need any heat treatment during drawing and before stranding.

CHEMICAL COMPOSITION %
Alloy Si Fe Cu Min Mg Cr Zn Ti Al
1050 0.25 max. 0.40 max. 0.05 max. 0.05 max. 0.05 max. - 0.05 max. 0.03 max. 99.50 min.
1060 0.25 max. 0.35 max. 0.05 max. 0.03 max. 0.03 max. - 0.05 max. 0.03 max. 99.60 min.
1070 0.20 max. 0.25 max. 0.04 max. 0.03 max. 0.03 max. - 0.04 max. 0.03 max. 99.70 min.
1100 0.95 max. 0.95 max. 0.05 - 0.20 0.05 max. - - 0.10 max. - 99.00 min.
1200 1.00 max. 1.00 max. 0.05 max. 0.05 max. - - 0.10 max. 0.05 max. 99.00 min.
3003 0.6 max. 0.7 max. 0.05 - 0.20 1.0 – 1.5 - - 0.10 max. - Rem
3005 0.6 max. 0.7 max. 0.30 max. 1.0 – 1.5 0.2 – 0.6 0.10 max. 0.25 max. 0.10 max. Rem
3105 0.6 max. 0.7 max. 0.30 max. 0.30 – 0.8 0.20 – 0.8 0.20 max. 0.40 max. 0.10 max. Rem
5005 0.30 max. 0.7 max. 0.20 max. 0.20 max. 0.50 – 1.1 0.10 max. 0.25 max. - Rem
5052 0.25 max. 0.40 max. 0.10 max. 0.10 max. 2.2 – 2.8 0.15 - 0.35 0.10 max. - Rem
5086 0.40 max. 0.50 max. 0.10 max. 0.2 – 0.7 3.5 – 4.50 0.05 - 0.25 0.25 max. 0.15 max. Rem
8011 0.50 – 0.9 0.6 – 1.0 0.10 max. 0.20 max. 0.05 max. 0.05 max. 0.10 max. 0.08 max. Rem
                   
WIDTH TOLERANCE ± 2.0 MM     LENGTH TOLEANCE ± 3.0 MM
ALLUMINIUM SHEET RANGE
Alloy Temper Thickness (mm) Width (mm) Length (mm)
1050 / 1060 / 1070 H1 / H2 / H3 / H4 / O 0.40 – 50 500 - 1500 1000 - 5500
1100 / 1200 / 8011 H1 / H2 / H3 / H4 / O 0.40 – 50 500 - 1500 1000 - 5500
3003 / 3105 / 3005 H1 / H2 / H3 / H4 0.40 – 50 500 - 1500 1000 - 5500
5005 / 5052 / 5086 / 5754 H1 / H2 / H3 / H4 0.40 – 50 500 - 1500 1000 - 5500
         

Note : Kindly indicate details of end application to help us suggest quality of the material i.e through hot mill route or concast route.

Note : MOQ conditions shall apply.

Specified Thickness Tolerance (± mm)
Over Thru Upto 1000mm Width Over 1000mm Width
0.40 0.63 0.05 0.08
0.63 0.80 0.06 0.09
0.08 1.00 0.07 0.10
1.00 1.20 0.08 0.11
1.20 1.60 0.08 0.12
1.60 2.00 0.09 0.14
2.00 2.50 0.10 0.16
2.50 3.20 0.12 0.18
3.20 4.00 0.14 0.22